M-7026 CR ICP DAS new

The M-7026 is a multifunction module that includes 6 analog input channels, 2 analog output channels, 3 digital input channels, 3 digital output channels. It provides a programmable input range on all analog input (+/-150 mV, +/-500 mV, +/-1 V, +/-5 V, +/-10 V, +/-20 mA or 0 ~ +20 mA), analog outputs are 12-bit at +/-5 V, +/-10 V, 0 ~ +20 mA or +4 ~ +20 mA and all digital outputs can be set as alarm output. Each analog input can be configured for an individual range and provides a high overvoltage protection of 240 Vrms. Voltage and current inputs/outputs are jumper selectable.
M-7026 CR: 6-channel Analog Input, 2-channel Analog Output, 3-channel Digital Input and 3-channel Digital Output Module using the DCON and Modbus Protocol (Gray Cover) (RoHS)

• Multifunction (6 AI, 2 AO, 3 DI and 3 DO)
• Supports Fast Mode and Normal Mode
• Individual Channel Configuration
• Oper Wire Detection for Current Output
• Overload and Short Circuit Protection for Digital Output
• Configurable Power-on Value Settings
• 240 Vrms Overvoltage Protection for Voltage Input
• Jumper Selectable Voltage or Current Input/Output
• Dual Watchdog
• +/- 7 kV Contact ESD Protection
• Wide Operating Temperature Range: - 25 ~ +75°C

Analog Input

Channels: 6
Wiring: Differential 
Range: ±150 mV, ±500 mV, ±1 V, ±5 V, ±10 V, ±20 mA , 0 ~ 20 mA, 4 ~ 20 mA(Jumper Selectable)
Resolution: 16-bit
Accuracy: Normal Mode = ±0.1% of FSR - Fast Mode = ±0.5% or better
Sampling Rate: Normal Mode = 10 Samples/Sec. - Fast Mode = 60 Samples/Sec. (Total)
Bandwidth: Normal Mode = 15.7 Hz - Fast Mode = 78.7 Hz
Input Impedance: Voltage = 2 MΩ - Current = 140 Ω
Common Voltage Protection: +/- 200 V
Individual Channel Configuration: Yes
Overvoltage Protection: 240 Vrms
Overcurrent Protection: Yes, 50 mA at 110 VDC
Virtual Channel to Channel Isolation: Yes, 400 VDC
Open Wire Detection for 4 ~ 20 mA: Yes 

Analog Output

Channels: 2
Range: +0 ~ +5 VDC, +0 ~ +10 VDC, ±5 VDC, ±10 VDC, +0 ~ +20 mA, +4 ~ +20 mA (Jumper Selectable)
Resolution: 12-bit
Accuracy: ±0.1% of FSR
Output Capacity Voltage Output Capability: 10 V @ 20 mA
Open Wire Detection: Yes, for 4 ~ 20 mA only
Power-on Value: Yes, Programmable
Safe Value: Yes, Programmable 

Digital Input/Counter

Channels: 3
Type: Dry Contact: Source - Wet Contact: --
Wet Contact: --
Dry Contact: On Voltage Level: Close to GND - Off Voltage Level: Open
Counters: Max. Count = 65535 (16-bit) - Max. Input Frequency = 50 Hz - Min. Pulse Width = 5 ms
Input Impedance: --
Channel-to-Channel Isolation: -- 
Overvoltage Protection: -- 
Safe Value: Yes, Programmable 

Digital Output

Output Channels: 3
Type: Open Collector
Sink/Source (NPN/PNP): Sink
Load Voltage: + 3.5 VDC ~ + 50 VDC
Max. Load Current: 700 mA/Channel
Overvoltage Protection: 60 VDC
Overload Protection: Yes
Short-circuit Protection: Yes
Power-on Value: Yes, Programmable
Safe Value: Yes, Programmable 

Communication

Interface: RS-485
RS-485 Bias Resistor: No (An RS-485 master is required to provide the bias)
Format: N, 8, 1
Baud Rate: 1200 ~ 115200 bps
Protocol: Modbus RTU, DCON
Dual Watchdog: Yes, Module (1.6 Seconds), Communication (Programmable) 

LED Indicators/Display

System LED Indicator: Yes, 1 LED as Power/Communication Indicator
I/O LED Indicatos: --
7-Segment LED Display: -- 

Isolation

Intra-module Isolation, Field-to-Logic: 2500 VDC 

EMS Protection

ESD (IEC 61000-4-2): ±4 kV Contact for each Terminal - ±8 kV Air for random point
EFT (IEC 61000-4-4): ±4 kV for Power Line
Surge (IEC 61000-4-5): ±3 kV for Power Line 

Power 

Reverse Polarity Protection: Yes 
Input Range: 10 ~ 30 VDC
Consumption: 1.8 W 

Mechanical

Dimensions (W x L x H): 72 mm x 123 mm x 35 mm
Installation: DIN-Rail or Wall Mounting 

Environment

Operating Temp.: -25 ~ +75°C
Storage Temp.: -40 ~ +85°C
Humidity: 10 ~ 95%RH, non-condensing