Benvenuti sulla nostra nuova piattaforma ICP DAS
Che sostituisce industrialtech.it

PISO-DNM100U-T ICP DAS Universal PCI Boards

PISO-DNM100U-T ICP DAS

PISO-DNM100U-T

1 Port Intelligent DeviceNet Master Universal PCI Board

Price

€ 517,59

(VAT excluded)

€ 631,46(VAT included)

Prezzo di 1 pz. iva (22%) inclusa: € 631,46

Availability: Not Available

SKU: 4679

Model: PISO-DNM100U-T

Need Help?


  • DeviceNet Version: Volume I & II, Release 2.0

  • Programmable master MAC ID and baud rate

  • Baud Rate: 125 kbps, 250 kbps, 500 kbps

  • Support Group 2 and UCMM connection

  • I/O Operating Modes: Poll, Bit-Strobe, Change of State / Cyclic

  • I/O Length: max 512 input bytes and 512 output bytes pre slave

  • Slave Node: 63 nodes max

  • Support auto-search slave device function

  • Support on-line adding and removing devices

  • Support auto-detect Group 2 and UCMM device

  • Auto-reconnect when the connection is broken

  • LED: Status,ERR


PISO-DNM100 can represent an economic solution of DeviceNet application and be a DeviceNet master device on the DeviceNet network. It is a "Predefined Master-Slave connection Set". PISO-DNM100 supports Group 2 only Server and UCMM functions to communication with slave devices. It has an independent CAN bus communication port and has the ability to cover a wide range of DeviceNet applications.

Besides, PISO-DNM100 uses the new CAN controller Phillips SJA1000T and transceiver 82C250/251, which provide bus arbitration, error detection with auto correction and re-transmission function.It can be installed on almost any windows-based system, for example Win98/Win2000/WinXP. It is popularly applied in the industrial automation, building automation, vehicle, marine, and embedded control network. In order to expand the DeviceNet functions of ICPDAS products, PISO-DNM100 is developed for this purpose.

APPLICATIONS

- Industrial Machinery •
- Building Automation •
- Medical •
- Maritime •
- Restaurant Appliances
- Laboratory Equipment &
- Research

FIRMWARE FEATURES

Programmable Master MAC ID
Programmable transfer-rate 125 kbps, 250 kbps, 500 kbps
Each port support maximum nodes up to 64
Support Group 2 Only Server functions
Support UCMM functions
Predefined Master-Slave Connection Set
The maximum Fragment number is (Input/Output) up to 64
Support I/O Operation Mode: Poll, Bit-Strobe and Change Of State/Cyclic
Support Auto-Scan slave device function
Support on-line adding and removing devices
Support boot-up auto communicating with slave devices
Support Auto-Reconnect when the connection is broken

MEMORY MAP OF REMOTE I/O

 
There exist two memory areas, “Input Area” and “Output Area”. The input data of all DeviceNet slaves would be stored in the “Input Area” by DeviceNet master scan engine. Oppositely, the output data of those DeviceNet slaves would be in the “Output Area”. Please refer to the following figure.
Users can read a bulk data from “Input Area” in the DeviceNet Master module, like PISO-DNM100U or I-8124W. This bulk data contains multiple devices’ input statuses. If one of the input status of the remote DeviceNet slave changes, the corresponding data located in the “Input Area” would change immediately. Oppositely, the “Output Area” contains multiple devices’ output data. Users may change the output value of a certain device by changing the corresponding data located in the “Output Area”.

TOOLKIT

Development Toolkit for Windows NT4.0
Development Toolkit for Windows 98/ME
Development Toolkit for Windows 2000/XP/Vista
Development Toolkit for Windows 7 32-bit
 

SOFTWARE UTILITY FEATURES

Diagnosis
This utility supports to search all devices and specific devices in the network. These functions help the users to configure the connection of the slave devices. Anymore, the software also can diagnose the remote slave devices when building the DeviceNet network.
Configuration
This software supports the users to configure the I/O connection of the devices by searching devices or manual setting. After configuring the I/O connection, the information would be saved into the EEPROM. The users can export the data from the EEPROM easily. Correspondingly, the users can import the data into the EEPROM.
Remote I/O access
The software utility can easily to access the I/O data of all the slave devices. The users can monitor the input data of the specific slave device and change the output data to the remote slave device with this utility.

Bus Interface

Type Universal PCI supports both 5 V and 3.3 V PCI bus
Board No. By DIP switch


CAN Interface

Controller NXP SJA1000T with 16 MHz clock  -  Microprocessor inside with 80186 80MHz
Transceiver NXP 82C250
Channel number  1
Connector 5-pin screwed terminal block (CAN_L, CAN_SHLD, CAN_H, N/A for others)
Baud Rate (bps) 125 k, 250 k, 500 k
Transmission Distance (m) Depend on baud rate (for example, max. 1000 m at 50 kbps )
Isolation 3000 VDC for DC-to-DC, 2500 Vrms for photo-couple
Terminator Resistor Jumper for 120 Ω terminator resistor
Specification ISO-11898-2, CAN 2.0A and CAN 2.0B
Protocol DeviceNet Volumn I ver2.0, Volumn II ver2.0


LED

Round LED Green LED, Red LED


Software

Driver Windows 98/ME/NT/2K/XP
Library VB 6.0, VC++ 6.0, BCB 6.0


Power

Power Consumption 300 mA @ 5 V


Mechanism

Dimensions 138mm x 22mm x 105mm (W x L x H)


Environment

Operating Temp. 0 ~ 60 ℃
Storage Temp. -20 ~ 70 ℃
Humidity 5 ~ 85% RH, non-condensing

Disclaimer